Re-add Scratch old 2.0 left alignment

372005

In scratch 2.0, I want to make my project clean and straight so my viewer can just use their mouse wheel to scroll down to see my project block by block. However, in scratch 3.0, the vertical alignment is no more I know the purpose of this is to make the block always visible/ in the middle of the screen, but this is annoying. I wish you could re-add the vertical alignment again, because it will make my blocks placements more beautiful vertically.

DarthVader4Life

Editing out some cringe

Last edited by DarthVader4Life (May 11, 2021 01:40:04)

372005

DarthVader4Life wrote:
so you want to revert to older versions basically, that's been rejected. correct me if i'm wrong.

Sorry, no. What I meant is re-add it you know. Not reverting back. Because now if you look inside any project now you will be that everything is messy, making it hard to figure it out how it works basically. It should be better if everything is in a straight line from top to bottom not to the left, to the right, ect… because basically I use the mouse wheel a lot to scroll up and down. If that project is not line up horizontally, I need to drag the bottom bar just to see what's on the right/left side

kenny2scratch

Do you mean how 2.0 had a limit to how far left or up you could scroll?

DarthVader4Life

372005 wrote:
Sorry, no. What I meant is re-add it you know. Not reverting back. Because now if you look inside any project now you will be that everything is messy, making it hard to figure it out how it works basically. It should be better if everything is in a straight line from top to bottom not to the left, to the right, ect… because basically I use the mouse wheel a lot to scroll up and down. If that project is not line up horizontally, I need to drag the bottom bar just to see what's on the right/left side

OK then, better have it as on option.

Last edited by DarthVader4Life (Aug. 16, 2021 22:15:51)

Nambaseking01

Could you please elaborate? I do not understand.

372005

Nambaseking01 wrote:
Could you please elaborate? I do not understand.

when green flag clicked
When you drag the
blocks
To the left side of the command area, it will automatically align it right next to the left side of the command area. 2.0 However in 3.0, this was remove.

Now if you drag the
blocks
then it will create more space to left of the command area.
Because now if you look inside any project now you will be that everything is messy, making it hard to figure it out how it works basically. It should be better if everything is in a straight line from top to bottom not to the left, to the right, ect… because basically I use the mouse wheel a lot to scroll up and down. If that project is not line up horizontally, I need to drag the bottom bar just to see what's on the right/left side

372005

kenny2scratch wrote:
Do you mean how 2.0 had a limit to how far left or up you could scroll?

Sorry, no. What I meant is
When you drag the
blocks
To the left side of the command area, it will automatically align it right next to the left side of the command area. 2.0 However in 3.0, this was remove.
Now if you drag the
blocks
then it will create more space to left of the command area.
_ _
Because now if you look inside any project now you will be that everything is messy, making it hard to figure it out how it works basically. It should be better if everything is in a straight line from top to bottom not to the left, to the right, ect… because basically I use the mouse wheel a lot to scroll up and down. If that project is not line up horizontally, I need to drag the bottom bar just to see what's on the right/left side

Last edited by 372005 (Sept. 24, 2019 14:51:25)

372005

Ok so everyone if you're confusing about the left side of the command block alignment then I'm working on it. Images of explaining it will be posted tomorrow. Please be patient

372005

Nambaseking01 wrote:
Could you please elaborate? I do not understand.

kenny2scratch wrote:
Do you mean how 2.0 had a limit to how far left or up you could scroll?

If you put the block like this

Then it should align perfect like this

Again, with 2 blocks separated to compare

But, in 3.0
look what happen

a demonstration of the new system:

if <You still not understand what I meant> then
say [Sorry,... Maybe you should quote me back explaining what you didn't understand about.] for (2) secs
else
say [I'm happy to hear that! Maybe quote me back saying something?] for (2) secs
end

define 2.0 images Is not real, I use paint to kind of make it understandable, but 2.0 still works that way

Last edited by 372005 (Sept. 25, 2019 04:17:59)

Discuss Scratch